ProGps - Queclink GV800
Server port: | 21644 |
Parameter name | Description | Units |
---|---|---|
csq_rssi | The GSM signal strength level. The range is 0-31, 99 for unknown | |
csq_ber | The quality of the GSM signal. The range is 0-7, 99 for unknown | |
is_pwr_ext | Whether the external power supply is connected. |
|
pwr_ext | The voltage of the external power supply | V |
pwr_int | The voltage of the backup battery. The value of this field is only valid when the external power is not connected | V |
charging | Whether the backup battery is charging when the main power supply is connected. |
|
led_on | Indicate whether the LED’s are turned on | |
input_id | ID of the input to which the fuel sensor is connected to, 0 means connected with serial port | |
battery | The current volume of the backup battery | % |
1wire | 1wire device data | |
harsh_speed_level | The speed level of which the harsh behavior is detected: |
|
harsh_behavior | Harsh behavior: |
|
can_state | CANBUS Device State: |
|
can_vin | Vehicle identification number | |
can_ignition_key | Ignition status: |
|
can_total_dist_hect | Vehicle total distance | Hectometer (H) |
can_total_dist_imp | Vehicle total distance | Impulse (I) |
can_total_fuel_used | Number of liters of fuel used since vehicle manufacture or device installation | L |
can_engine_rpm | The revolutions per minute | rpm |
can_vehicle_speed | The vehicle speed based on wheel | km/h |
can_eng_cool_temp | Engine coolant temperature | °C |
can_fuel_consumpt | The fuel consumption. The consumption is calculated depending on values read from vehicle. |
|
can_fuel_level_l | The level of fuel in vehicle tank | L |
can_fuel_level_p | The level of fuel in vehicle tank | % |
can_range | The number of hectometer to drive on remaining fuel | Hectometer (H) |
can_acc_pedal_press | Accelerator pedal pressure | % |
can_total_eng_hours | Time of engine running since vehicle manufacture or device installation | h |
can_total_driv_time | Time of engine running (non-zero speed) since vehicle manufacture or device installation | h |
can_eng_idle_time | Time of engine running during idling status (vehicle stopped) since vehicle manufacture or device installation | h |
can_idle_fuel_used | Total idle fuel used. Number of liters of fuel used since vehicle manufacture or device installation | L |
can_axle_weight | Vehicle axle weight | kg |
can_driverN_time_st | Driver N time related states: |
|
can_driverN_card | Driver N card state: |
|
can_driverN_work_st | Driver N work state: |
|
can_indicators | Detailed Information/Indicators: |
|
can_light | Each bit contains information of particular light: |
|
can_doors | Each bit contains information of one door: |
|
can_total_veh_ovspd | The total time when vehicle engine speed is greater than the limit defined in CAN100's configuration | |
can_total_eng_ovspd | The total time when vehicle engine speed is greater than the limit defined in CAN100's configuration | |
can_ad_blue_lvl | The level of Ad-Blue | |
tacho_ovspd_sign | The tachograph overspeed signal. The value 1 indicates "overspeed". The value 0 indicates "no overspeed" | |
tacho_motion_sign | The tachograph vehicle motion signal. The value 1 indicates "motion". The value 0 indicates "no motion" | |
tacho_direction | Vehicle driving direction obtained from tachograph | |
can_ain1 | The value of analog input | mV |
can_engine_braking_factor | Counts of braking with brake pedal or with engine | |
can_pedal_braking_factor | Counts of braking with brake pedal or with engine | |
can_total_accel_kickdowns | Total time when accelerator pedal is pressed over 90% | |
can_total_brakes | The total number of braking processes initiated by brake pedal | |
tacho_drvN_card_number | The card number of tachograph driver N | |
can_exp_info | Detailed Information/Indicators: |
|
can_rapid_brakings | Number of total rapid since installation | |
can_rapid_accels | Number of total rapid accelerations since installation |